 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| inductors slf6025 slf6028 slf6045 slf7032 slf7045 slf7055 slf10145 slf10165 slf12555 slf12565 slf12575 july 2013 inductors for power circuits wound ferrite slf series
(2/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 6 months. be sure to follow the storage conditions (temperature: 5 to 30c, humidity: 10 to 75 % rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (cars, electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders (3/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. inductors for power circuits wound ferrite features magnetic shield type wound ind uctor for power circuits. product lineup allows for various usages. application thin-screen tv, lcds, av equipment, gaming equipment, other electrical devices part number construction operating temperature range, pack age quantity, product weight operating temperature range includes self-temperature rise. the storage temperature range is for after the circuit board is mounted. product compatible with rohs directive compatible with lead-free solders overview of the slf series slf 6025 t - 4r7 m 1r5 - pf series name lwh dimensions packaging style inductance inductance tolerance rated current internal code (mm) (h) (a) 6025 6.06.02.5 t taping 1r0 1.0 m 20% r47 0.47 6028 6.06.02.8 100 10 n 30% 2r2 2.2 6045 6.06.04.5 101 100 150 15 7032 7.07.03.2 7045 7.07.04.5 7055 7.07.05.5 10145 10.110.14.5 10165 10.110.16.8 12555 12.512.55.5 12565 12.512.56.5 12575 12.512.57.5 type temperature range package quantity individual weight operating temperature storage temperature c c (pieces/reel) g slf6025 C40 to +105 C40 to +105 1000 0.3 slf6028 C40 to +105 C40 to +105 1000 0.3 slf6045 C40 to +105 C40 to +105 1000 0.4 slf7032 C40 to +105 C40 to +105 1000 0.4 slf7045 C40 to +105 C40 to +105 1000 0.6 slf7055 C40 to +105 C40 to +105 1000 0.8 slf10145 C40 to +105 C40 to +105 500 1.3 slf10165 C40 to +105 C40 to +105 500 1.9 slf12555 C40 to +105 C40 to +105 500 2.6 slf12565 C40 to +105 C40 to +105 500 3.2 slf12575 C40 to +105 C40 to +105 500 3.6 rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://www.t dk.co.jp/rohs/ (4/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. overview of the slf series recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 60 to 120s 230c 30s 250c 5s natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature (5/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series slf6025 type shape & dimensions recommended land pattern 60.2 60.2 20.1 2.50.2 4 0.9 0.9 4r7 dimensions in mm dimensions in mm 4 1.5 1.5 2.2 (6/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf6025 type electrical characteristics characteristics specification table rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (30% below the nominal value) idc2: when based on the temperature increase (temperature increase of 25c by self heating) measurement equipment ? equivalent measurement equipment may be used. l l measuring frequency (khz) dc resistance ( )20% rated current(a) part no. max. (h) tolerance idc1 idc2 4.7 20% 100 0.0306 1.5 1.8 slf6025t-4r7m1r5-pf 6.8 20% 100 0.0442 1.3 1.5 slf6025t-6r8m1r3-pf 10 20% 100 0.0573 1 1.3 slf6025t-100m1r0-pf 15 20% 100 0.085 0.88 1.1 slf6025t-150mr88-pf 22 20% 100 0.122 0.73 0.94 slf6025t-220mr73-pf 33 20% 100 0.18 0.59 0.79 slf6025t-330mr59-pf 47 20% 100 0.24 0.48 0.67 slf6025t-470mr48-pf 68 20% 100 0.37 0.42 0.54 slf6025t-680mr42-pf 100 20% 100 0.5 0.33 0.47 slf6025t-101mr33-pf measurement item product no. manufacturer l 4194a agilent technologies dc resistance vp-2941a panasonic rated current idc1 4284a+42841a+42842c agilent technologies (7/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf6025 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 1 10 100 1000 1 10 100 1000 10000 100000 1000000 inductance ( h ) frequency ( khz ) 100m 6r8m 4r7m 220m 330m 470m 680m 101m 150m product no. manufacturer 4294a agilent technologies (8/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf6025 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. 100m 6r8m 4r7m 220m 330m 150m dc current ( a ) 0.1 3 1 100 1000 300 30 10 1 0.3 3 10 inductance ( h ) product no. manufacturer 4284a+42841a+42842c agilent technologies (9/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series slf6028 type shape & dimensions recommended land pattern dimensions in mm 60.2 60.2 20.1 2.80.2 4 0.9 0.9 4r7 dimensions in mm 4 1.5 1.5 2.2 (10/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf6028 type electrical characteristics characteristics specification table rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (30% below the nominal value) idc2: when based on the temperature increase (temperature increase of 25c by self heating) measurement equipment ? equivalent measurement equipment may be used. l l measuring frequency (khz) dc resistance ( )20% rated current(a) part no. max. (h) tolerance idc1 idc2 4.7 20% 100 0.0284 1.6 2.5 slf6028t-4r7m1r6-pf 6.8 20% 100 0.0354 1.5 2.2 slf6028t-6r8m1r5-pf 10 20% 100 0.0532 1.3 1.8 slf6028t-100m1r3-pf 15 20% 100 0.0745 1 1.4 slf6028t-150m1r0-pf 22 20% 100 0.104 0.77 1.3 slf6028t-220mr77-pf 33 20% 100 0.148 0.69 1.1 slf6028t-330mr69-pf 47 20% 100 0.21 0.59 0.92 slf6028t-470mr59-pf 68 20% 100 0.29 0.5 0.78 slf6028t-680mr50-pf 100 20% 100 0.43 0.42 0.64 slf6028t-101mr42-pf 150 20% 100 0.65 0.34 0.5 slf6028t-151mr34-pf 220 20% 100 0.98 0.26 0.38 slf6028t-221mr26-pf measurement item product no. manufacturer l 4194a agilent technologies dc resistance vp-2941a panasonic rated current idc1 4284a+42841a+42842c agilent technologies (11/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf6028 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 1 10 100 1000 1 10 100 1000 10000 100000 1000000 inductance ( h ) frequency ( khz ) 330m 470m 680m 221m 101m 151m 100m 6r8m 4r7m 220m 150m product no. manufacturer 4294a agilent technologies (12/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf6028 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. dc current ( a ) inductance ( h ) 1 10 100 1000 0.0 0.5 1.0 1.5 2.0 2.5 330m 470m 680m 221m 101m 151m 100m 6r8m 4r7m 220m 150m product no. manufacturer 4284a+42841a+42842c agilent technologies (13/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series slf6045 type shape & dimensions recommended land pattern dimensions in mm 60.2 60.2 20.1 4.50.3 4 0.9 0.9 4r7 dimensions in mm 4 1.5 1.5 2.2 (14/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf6045 type electrical characteristics characteristics specification table rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (10% below the initial value) idc2: when based on the temperature increase (temperature increase of 30c by self heating) measurement equipment ? equivalent measurement equipment may be used. l l measuring frequency (khz) dc resistance (m ) rated current(a) part no. max. (h) tolerance idc1 idc2 1.5 30% 100 1630% 4 4.1 slf6045t-1r5n4r0-3pf 2.2 30% 100 1830% 3.3 3.8 slf6045t-2r2n3r3-3pf 3.3 30% 100 21.530% 2.8 3.4 slf6045t-3r3n2r8-3pf 4.7 30% 100 26.530% 2.4 3.2 slf6045t-4r7n2r4-3pf 6.8 30% 100 3330% 2 2.8 slf6045t-6r8n2r0-3pf 10 20% 100 3920% 1.6 2.7 slf6045t-100m1r6-3pf 15 20% 100 59.520% 1.3 2.'2 slf6045t-150m1r3-3pf 22 20% 100 8220% 1.1 1.8 slf6045t-220m1r1-3pf measurement item product no. manufacturer l 4194a agilent technologies dc resistance vp-2941a panasonic rated current idc1 4284a+42841a+42842c agilent technologies (15/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf6045 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 1 10 100 1000 1 10 100 1000 10000 100000 10000000 1000000 inductance ( h ) frequency ( mhz ) 3r3n 2r2n 1r5n 100m 6r8n 4r7n 220m 150m product no. manufacturer 4294a agilent technologies (16/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf6045 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0 2 4 6 8 1 10 dc current ( a ) inductance ( h ) 100 3r3n 2r2n 1r5n 100m 6r8n 4r7n 220m 150m product no. manufacturer 4284a+42841a+42842c agilent technologies (17/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series slf7032 type shape & dimensions recommended land pattern dimensions in mm 70.2 70.2 20.1 3.20.2 4.9 0.9 0.9 4r7 dimensions in mm 4.8 1.5 1.5 2.2 (18/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf7032 type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. l l measuring frequency (khz) dc resistance ( )20% rated current(a) max. part no. (h) tolerance 3.3 20% 100 0.023 1.9 slf7032t-3r3m1r9-2pf 4.7 20% 100 0.030 1.7 slf7032t-4r7m1r7-2pf 6.8 20% 100 0.041 1.6 slf7032t-6r8m1r6-2pf 10 20% 100 0.053 1.4 slf7032t-100m1r4-2pf 15 20% 100 0.075 1.1 slf7032t-150m1r1-2pf 22 20% 100 0.11 0.96 slf7032t-220mr96-2pf 33 20% 100 0.16 0.75 slf7032t-330mr75-2pf 47 20% 100 0.24 0.67 slf7032t-470mr67-2pf 68 20% 100 0.31 0.59 slf7032t-680mr59-2pf 100 20% 100 0.45 0.45 slf7032t-101mr45-2pf 150 20% 100 0.65 0.37 slf7032t-151mr37-2pf 220 20% 100 1.05 0.29 slf7032t-221mr29-2pf 330 20% 100 1.67 0.22 slf7032t-331mr22-2pf 470 20% 100 2.05 0.2 slf7032t-471mr20-2pf 680 20% 100 3.15 0.16 slf7032t-681mr16-2pf 1000 20% 100 4.78 0.13 slf7032t-102mr13-2pf measurement item product no. manufacturer l 4194a agilent technologies dc resistance vp-2941a panasonic rated current idc1 4284a+42841a+42842c agilent technologies (19/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf7032 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 1 10 100 100000 10000 1000 1 10 100 1000 10000 inductance ( h ) frequency ( khz ) 102m 681m 471m 331m 221m 151m 101m 680m 470m 330m 220m 150m 100m 6r8m 4r7m 3r3m product no. manufacturer 4294a agilent technologies (20/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf7032 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. dc current ( a ) inductance ( h ) 1 10 100 1000 10000 0 0.5 1 1.5 2 2.5 3 102m 681m 471m 331m 221m 151m 101m 680m 470m 330m 220m 150m 100m 6r8m 4r7m 3r3m product no. manufacturer 4284a+42841a+42842c agilent technologies (21/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series slf7045 type shape & dimensions recommended land pattern dimensions in mm 70.2 70.2 20.1 4.50.3 4.9 0.9 0.9 4r7 dimensions in mm 4.8 1.5 1.5 2.2 (22/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf7045 type electrical characteristics characteristics specification table rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (10% below the initial value) idc2: when based on the temperature increase (temperature increase of 20c by self heating) measurement equipment ? equivalent measurement equipment may be used. l l measuring frequency (khz) dc resistance ( )20% rated current(a) part no. max. (h) tolerance idc1 idc2 3.3 20% 100 0.02 2.5 2.3 slf7045t-3r3m2r5-pf 4.7 20% 100 0.03 2 2.1 slf7045t-4r7m2r0-pf 6.8 20% 100 0.039 1.7 1.74 slf7045t-6r8m1r7-pf 10 20% 100 0.036 1.3 1.78 slf7045t-100m1r3-pf 15 20% 100 0.052 1.1 1.53 slf7045t-150m1r1-pf 22 20% 100 0.061 0.9 1.34 slf7045t-220mr90-pf 33 20% 100 0.096 0.82 1.09 slf7045t-330mr82-pf 47 20% 100 0.125 0.75 0.92 slf7045t-470mr75-pf 68 20% 100 0.175 0.6 0.77 slf7045t-680mr60-pf 100 20% 100 0.25 0.5 0.65 slf7045t-101mr50-pf 150 20% 100 0.34 0.4 0.55 slf7045t-151mr40-pf 220 20% 100 0.52 0.33 0.45 slf7045t-221mr33-pf 330 20% 100 0.74 0.25 0.37 slf7045t-331mr25-pf 470 20% 100 1.05 0.22 0.31 slf7045t-471mr22-pf 680 20% 100 1.48 0.2 0.27 slf7045t-681mr20-pf 1000 20% 100 2.28 0.14 0.25 slf7045t-102mr14-pf measurement item product no. manufacturer l 4194a agilent technologies dc resistance vp-2941a panasonic rated current idc1 4284a+42841a+42842c agilent technologies (23/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf7045 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 1 10 100 10000 1000 1 10 100 1000 10000 100000 1000000 inductance ( h ) frequency ( khz ) 471m 331m 102m 681m 101m 680m 221m 151m 470m 150m 100m 6r8m 4r7m 3r3m 330m 220m product no. manufacturer 4294a agilent technologies (24/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf7045 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. 1 10 100 1000 10000 012 dc current ( a ) inductance ( h ) 3 680m 101m 151m 221m 331m 471m 681m 102m 3r3m 100m 6r8m 4r7m 220m 330m 470m 150m product no. manufacturer 4284a+42841a+42842c agilent technologies (25/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series slf7055 type shape & dimensions recommended land pattern dimensions in mm 70.2 70.2 20.1 5.50.3 4.9 0.9 0.9 4r7 dimensions in mm 2.2 4.8 1.5 1.5 (26/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf7055 type electrical characteristics characteristics specification table rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (10% below the initial value) idc2: when based on the temperature increase (temperature increase of 30c by self heating) measurement equipment ? equivalent measurement equipment may be used. l l measuring frequency (khz) dc resistance (m ) rated current(a) part no. max. (h) tolerance idc1 idc2 1.5 30% 100 17.430% 6.2 4 slf7055t-1r5n4r0-3pf 2.2 30% 100 21.730% 5.3 3.5 slf7055t-2r2n3r5-3pf 3.3 30% 100 2430% 4.3 3.3 slf7055t-3r3n3r3-3pf 4.7 30% 100 2830% 3.6 3.1 slf7055t-4r7n3r1-3pf 6.8 30% 100 3430% 3 2.8 slf7055t-6r8n2r8-3pf 10 20% 100 39.120% 2.6 2.5 slf7055t-100m2r5-3pf 15 20% 100 50.820% 2.1 2.2 slf7055t-150m2r1-3pf 22 20% 100 64.320% 1.7 2 slf7055t-220m1r7-3pf measurement item product no. manufacturer l 4194a agilent technologies dc resistance vp-2941a panasonic rated current idc1 4284a+42841a+42842c agilent technologies (27/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf7055 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 1 10 100 1000 1 10 100 1000 10000 100000 1000000 inductance ( h ) frequency ( mhz ) 3r3n 2r2n 1r5n 100m 6r8m 4r7n 220m 150m product no. manufacturer 4294a agilent technologies (28/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf7055 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. 01234 1 10 dc current ( a ) inductance ( h ) 100 56 3r3n 2r2n 1r5n 100m 6r8m 4r7n 220m 150m product no. manufacturer 4284a+42841a+42842c agilent technologies (29/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series slf10145 type shape & dimensions recommended land pattern dimensions in mm 10.10.3 10.10.3 30.1 4.50.3 6.1 22 100 dimensions in mm 5.6 2.5 2.5 3.2 (30/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf10145 type electrical characteristics characteristics specification table rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (10% below the initial value) idc2: when based on the temperature increase (temperature increase of 30c by self heating) measurement equipment ? equivalent measurement equipment may be used. l l measuring frequency (khz) dc resistance ( )20% rated current(a) part no. max. (h) tolerance idc1 idc2 3.3 30% 1 0.0161 4.9 3.7 slf10145t-3r3n3r7-pf 5.6 20% 1 0.0220 3.8 3.2 slf10145t-5r6m3r2-pf 10 20% 1 0.0364 3 2.5 slf10145t-100m2r5-pf 15 20% 1 0.0472 2.4 2.2 slf10145t-150m2r2-pf 22 20% 1 0.0591 2.1 1.9 slf10145t-220m1r9-pf 33 20% 1 0.0815 1.6 1.7 slf10145t-330m1r6-pf 47 20% 1 0.1 1.4 1.5 slf10145t-470m1r4-pf 68 20% 1 0.14 1.2 1.3 slf10145t-680m1r2-pf 100 20% 1 0.2 1 1.1 slf10145t-101m1r0-pf 150 20% 1 0.35 0.79 0.81 slf10145t-151mr79-pf 220 20% 1 0.47 0.65 0.7 slf10145t-221mr65-pf 330 20% 1 0.68 0.54 0.58 slf10145t-331mr54-pf 470 20% 1 1.03 0.47 0.47 slf10145t-471mr47-pf 680 20% 1 1.6 0.38 0.38 slf10145t-681mr38-pf 1000 20% 1 2.8 0.32 0.29 slf10145t-102mr29-pf 1500 20% 1 3.4 0.22 0.26 slf10145t-152mr22-pf measurement item product no. manufacturer l 4194a agilent technologies dc resistance vp-2941a panasonic rated current idc1 4284a+42841a+42842c agilent technologies (31/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf10145 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 1 10 100 100000 10000 1000 1 10 100 1000 10000 100000 inductance ( h ) frequency ( khz ) 152m 102m 681m 471m 331m 221m 151m 101m 680m 470m 330m 220m 150m 100m 5r6m 3r3n product no. manufacturer 4294a agilent technologies (32/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf10145 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. dc current ( a ) inductance ( h ) 1 10 100 1000 10000 01234 152m 102m 681m 471m 331m 221m 151m 101m 680m 470m 330m 220m 150m 100m 5r6m 3r3n product no. manufacturer 4284a+42841a+42842c agilent technologies (33/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series slf10165 type shape & dimensions recommended land pattern dimensions in mm 10.10.3 10.10.3 30.1 6.50.3 6.1 22 100 dimensions in mm 3.2 5.6 2.5 2.5 (34/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf10165 type electrical characteristics characteristics specification table rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (10% below the initial value) idc2: when based on the temperature increase (temperature increase of 30c by self heating) measurement equipment ? equivalent measurement equipment may be used. l l measuring frequency (khz) dc resistance (m ) rated current(a) part no. max. (h) tolerance idc1 idc2 1.5 30% 100 6.730% 10.7 6.8 slf10165t-1r5n6r83pf 2.2 30% 100 8.430% 8.9 6.3 slf10165t-2r2n6r33pf 3.3 30% 100 9.630% 7.8 5.8 slf10165t-3r3n5r83pf 4.7 30% 100 11.730% 6.1 4.7 slf10165t-4r7n4r73pf 6.8 30% 100 1430% 4.6 4.3 slf10165t-6r8n4r33pf 10 20% 100 18.520% 4.1 3.8 slf10165t-100m3r83pf 15 20% 100 2720% 3.1 3.1 slf10165t-150m3r13pf 22 20% 100 44.820% 2.7 2.4 slf10165t-220m2r43pf measurement item product no. manufacturer l 4194a agilent technologies dc resistance vp-2941a panasonic rated current idc1 4284a+42841a+42842c agilent technologies (35/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf10165 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 3r3n 2r2n 1r5n 100m 6r8m 4r7n 220m 150m 10 0 100 1000 1 10 100 1000 10000 100000 inductance ( h ) frequency ( mhz ) product no. manufacturer 4294a agilent technologies (36/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf10165 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. 05 1 10 100 1000 dc current ( a ) inductance ( h ) 10 3r3n 2r2n 1r5n 100m 6r8n 4r7n 220m 150m product no. manufacturer 4284a+42841a+42842c agilent technologies (37/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series slf12555 type shape & dimensions recommended land pattern dimensions in mm 12.50.3 12.50.3 30.1 5.50.3 8.5 22 100 dimensions in mm 8.5 2.6 2.6 3.2 (38/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf12555 type electrical characteristics characteristics specification table rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (10% below the initial value) idc2: when based on the temperature increase (temperature increase of 30c by self heating) measurement equipment ? equivalent measurement equipment may be used. l l measuring frequency (khz) dc resistance ( )20% rated current(a) part no. max. (h) tolerance idc1 idc2 6 30% 1 0.0164 3.6 4.9 slf12555t-6r0n3r6-pf 10 20% 1 0.0215 3.4 4.3 slf12555t-100m3r4-pf 15 20% 1 0.0259 2.8 3.9 slf12555t-150m2r8-pf 22 20% 1 0.0338 2.3 3.4 slf12555t-220m2r3-pf 33 20% 1 0.0415 1.9 3.1 slf12555t-330m1r9-pf 47 20% 1 0.0618 1.6 2.5 slf12555t-470m1r6-pf 68 20% 1 0.0832 1.3 2.2 slf12555t-680m1r3-pf 100 20% 1 0.117 1.1 1.8 slf12555t-101m1r1-pf 150 20% 1 0.19 0.88 1.4 slf12555t-151mr88-pf 220 20% 1 0.27 0.72 1.2 slf12555t-221mr72-pf 330 20% 1 0.41 0.59 1 slf12555t-331mr59-pf 470 20% 1 0.52 0.49 0.88 slf12555t-471mr49-pf 680 20% 1 0.76 0.43 0.73 slf12555t-681mr43-pf 1000 20% 1 1.12 0.34 0.6 slf12555t-102mr34-pf 1500 20% 1 1.73 0.29 0.48 slf12555t-152mr29-pf measurement item product no. manufacturer l 4194a agilent technologies dc resistance vp-2941a panasonic rated current idc1 4284a+42841a+42842c agilent technologies (39/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf12555 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 10 1 100 100000 10000 1000 1 10 100 1000 10000 100000 inductance ( h ) frequency ( khz ) 152m 102m 681m 471m 331m 221m 151m 101m 680m 470m 330m 220m 150m 100m 6r0n product no. manufacturer 4294a agilent technologies (40/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf12555 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. dc current ( a ) inductance ( h ) 1 10 100 1000 10000 01234 152m 102m 681m 471m 331m 221m 151m 101m 680m 470m 330m 220m 150m 100m 6r0n product no. manufacturer 4284a+42841a+42842c agilent technologies (41/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series slf12565 type shape & dimensions recommended land pattern dimensions in mm 12.50.3 12.50.3 30.1 6.50.35 8.5 22 100 dimensions in mm 8.5 2.6 2.6 3.2 (42/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf12565 type electrical characteristics characteristics specification table rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (10% below the initial value) idc2: when based on the temperature increase (temperature increase of 40c by self heating) measurement equipment ? equivalent measurement equipment may be used. l l measuring frequency (khz) dc resistance ( )20% rated current(a) part no. max. (h) tolerance idc1 idc2 2 30% 1 0.0117 10 6.2 slf12565t-2r0n6r2-pf 4.2 30% 1 0.015 7.3 5.5 slf12565t-4r2n5r5-pf 7 30% 1 0.0177 5.7 5 slf12565t-7r0n5r0-pf 10 20% 1 0.0202 5 4.8 slf12565t-100m4r8-pf 15 20% 1 0.0237 4.2 4.4 slf12565t-150m4r2-pf 22 20% 1 0.0316 3.5 3.8 slf12565t-220m3r5-pf 33 20% 1 0.0406 2.8 3.4 slf12565t-330m2r8-pf 47 20% 1 0.0578 2.4 2.8 slf12565t-470m2r4-pf 68 20% 1 0.0787 2 2.4 slf12565t-680m2r0-pf 100 20% 1 0.123 1.6 1.9 slf12565t-101m1r6-pf 220 20% 1 0.273 1 1.2 slf12565t-221m1r0-pf measurement item product no. manufacturer l 4194a agilent technologies dc resistance vp-2941a panasonic rated current idc1 4284a+42841a+42842c agilent technologies (43/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf12565 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 10 1 100 10000 1000 1 10 100 1000 10000 100000 inductance ( h ) frequency ( khz ) 221m 101m 680m 470m 330m 220m 150m 100n 7r0n 2r0n 4r2n product no. manufacturer 4294a agilent technologies (44/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf12565 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. dc current ( a ) inductance ( h ) 10 0 1 10 100 1000 2468 221m 101m 680m 470m 330m 220m 150m 100n 7r0n 2r0n 4r2n product no. manufacturer 4284a+42841a+42842c agilent technologies (45/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series slf12575 type shape & dimensions recommended land pattern dimensions in mm 12.50.3 12.50.3 30.1 7.50.35 8.5 22 100 dimensions in mm 8.5 2.6 2.6 3.2 (46/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf12575 type electrical characteristics characteristics specification table rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (10% below the initial value) idc2: when based on the temperature increase (temperature increase of 40c by self heating) measurement equipment ? equivalent measurement equipment may be used. l l measuring frequency (khz) dc resistance ( )20% rated current(a) part no. max. (h) tolerance idc1 idc2 1.2 30% 1 0.0069 13 8.2 slf12575t-1r2n8r2-pf 2.7 30% 1 0.0094 10 7 slf12575t-2r7n7r0-pf 3.9 30% 1 0.0104 9 6.7 slf12575t-3r9n6r7-pf 5.6 30% 1 0.0116 7.8 6.3 slf12575t-5r6n6r3-pf 6.8 30% 1 0.0131 7.2 5.9 slf12575t-6r8n5r9-pf 10 20% 1 0.0156 5.5 5.4 SLF12575T-100M5R4-PF 15 20% 1 0.0184 4.7 5 slf12575t-150m4r7-pf 22 20% 1 0.0263 4 4 slf12575t-220m4r0-pf 33 20% 1 0.0395 3.2 3.4 slf12575t-330m3r2-pf 47 20% 1 0.0528 2.7 3 slf12575t-470m2r7-pf 68 20% 1 0.0778 2 2.4 slf12575t-680m2r0-pf 100 20% 1 0.125 1.9 1.9 slf12575t-101m1r9-pf 150 20% 1 0.175 1.5 1.6 slf12575t-151m1r5-pf 220 20% 1 0.258 1.3 1.3 slf12575t-221m1r3-pf measurement item product no. manufacturer l 4194a agilent technologies dc resistance vp-2941a panasonic rated current idc1 4284a+42841a+42842c agilent technologies (47/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf12575 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 1 10 100 10000 1000 1 10 100 1000 10000 100000 inductance ( h ) frequency ( khz ) 221m 151m 101m 680m 470m 330m 220m 150m 100m 5r6n 6r8n 3r9n 2r7n 1r2n product no. manufacturer 4294a agilent technologies (48/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series y slf12575 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. dc current ( a ) inductance ( h ) 1 10 100 1000 024681012 221m 151m 101m 680m 470m 330m 220m 150m 100m 5r6n 6r8n 3r9n 2r7n 1r2n product no. manufacturer 4284a+42841a+42842c agilent technologies (49/49) inductors 001-01 / 20130731 / inductor_commercial_power_slf_en.fm ? all specifications are subject to change without notice. slf series packaging style reel dimensions * these values are typical values. tape dimensions ty p e a w1 w2 n e slf6025 ?330 16.4 22.4 ?50 2 slf6028 ?330 16.4 22.4 ?50 2 slf6045 ?330 16.4 22.4 ?50 2 slf7032 ?330 16.4 22.4 ?50 2 slf7045 ?330 16.4 22.4 ?50 2 slf7055 ?330 16.4 22.4 ?50 2 slf10145 ?330 24.4 30.4 ?50 2 slf10165 ?330 24.4 30.4 ?50 2 slf12555 ?330 24.4 30.4 ?50 2 slf12565 ?330 24.4 30.4 ?50 2 slf12575 ?330 24.4 30.4 ?50 2 ?13.0 0.5 ?21.0 0.8 2.0 0.5 a ( 1.0 ) dimensions in mm n e w2 w1 fe w p0p2?d0 p1 a t b k dimensions in mm ty p e a b ?d0 e f p0 p1 p2 w k t slf6025 6.4 6.4 1.5+0.1/-0 1.750.1 7.50.1 4.00.1 12.00.1 2.00.05 16.00.3 3.1 0.4 slf6028 6.4 6.4 1.5+0.1/-0 1.750.1 7.50.1 4.00.1 12.00.1 2.00.05 16.00.3 3.1 0.4 slf6045 6.4 6.4 1.5+0.1/-0 1.750.1 7.50.1 4.00.1 12.00.1 2.00.05 16.00.3 4.9 0.4 slf7032 7.4 7.6 1.5+0.1/-0 1.750.1 7.50.1 4.00.1 12.00.1 2.00.05 16.00.3 3.6 0.4 slf7045 7.4 7.6 1.5+0.1/-0 1.750.1 7.50.1 4.00.1 12.00.1 2.00.05 16.00.3 4.8 0.4 slf7055 7.4 7.6 1.5+0.1/-0 1.750.1 7.50.1 4.00.1 12.00.1 2.00.05 16.00.3 5.5 0.4 slf10145 10.5 10.5 1.5+0.1/-0 1.750.1 11.50.1 4.00.1 16.00.1 2.00.05 24.00.3 5.0 0.4 slf10165 10.5 10.5 1.5+0.1/-0 1.750.1 11.50.1 4.00.1 16.00.1 2.00.05 24.00.3 7.1 0.4 slf12555 13 13 1.5+0.1/-0 1.750.1 11.50.1 4.00.1 16.00.1 2.00.05 24.00.3 6.0 0.4 slf12565 13 13 1.5+0.1/-0 1.750.1 11.50.1 4.00.1 16.00.1 2.00.05 24.00.3 7.0 0.34 slf12575 13 13 1.5+0.1/-0 1.750.1 11.50.1 4.00.1 16.00.1 2.00.05 24.00.3 8.0 0.34 |
Price & Availability of SLF12575T-100M5R4-PF
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |